Controlled and uncontrolled rectification (EP1/EP2)
Equipment for studying uncontrolled rectification (EP1), controlled rectification and alternating current regulation (EP2). It can be used at either low voltage (22/38 VAC, with CIR-120 and CRC- 120 charges) or mains voltage.
Are you interested
in this product?
Training module RNC-120
Ref.: MDULRNC120
UNCONTROLLED RECTIFICATION.
It enables the study of power diode-based rectifiers and their applications: single-phase, two-phase and three-phase half wave and full wave rectifiers.
- Based on the multi-panel concept.
- Includes the base module and five panels for study of the different bridges.
- Operating range: 22 VAC – 380 VAC.Safety connections and over-voltage and overload protection.
Training module MGI-120
Ref.: MDULMGI120
PULSE GENERATOR.
Sync and pulse train generator for ignition of the RTC-120 module thyristors.
- Control of up to 6 thyristors in three-phase bridge configuration.
- Three separate sync inputs, 10 – 380 VAC.
- Six pulse outputs, simultaneous and electrically insulated in pairs.
- Time-shifted pulse train according to external or internal set point.
- Input terminal for enabling/inhibiting pulse outputs.
- Requires ALI-700 ±15 V power supply module and table-mounted frame.
Training module RTC-120
Ref.: MDULRTC120
CONTROLLED RECTIFICATION.
It enables the study of power thyristor based controlled rectifiers and their applications: semi-controlled and fully controlled single-phase, two-phase and threephase half wave and full wave rectifiers.
- Based on the multi-panel concept.
- Includes the base module and eight panels for study of the different bridges.
- Operating range: 22 VAC – 380 VAC.
- Safety connections and over-voltage and overload protection.
Training Module BAT-120
Ref.: MDULBAT120
RECHARGEABLE BATTERY.
Module for simulating counter-electromotive force (DC motor), with single-phase 230 VAC mains supply. Charging circuit 12 V/6.5 Ah.
Training module TRI-120
Ref.: MDULCRC120
RESISTIVE-INDUCTIVE CHARGE.
Phase transformer, depending on the model has a ratio of 220 V. to 22/38 V. or 380 V. a 22/38 V, with an apparent power of 300 VA. It is required for obtaining a low-power three-phase system, supplying the RNC/RTC-120 modules.
- Selection of 22/38 V output voltage by selector switch.
- Successive phase indicator light.
- Overload and over-voltage protection.
- Requires ALI-700 ±15 V power supply module and table-mounted frame.
Training module CRC-120
Ref.: MDULCRC120
RESISTIVE-CAPACITIVE CHARGES.
Charge module for low-power rectifier bridge work.
- Multi-panel system.
- Three panels for configuring different types of charge connection.
- Charges: Y/A, free connection, etc., up to 63 Vef.
Training module CIR-120
Ref.: MDULCIR120
RESISTIVE-INDUCTIVE CHARGE.
Charge module for low-power rectifier bridge work.
- Multi-panel system.
- Twelve panels for configuring different charge connection types.
- Charges: Y/A, R, L, R-L, free connection, etc., up to 50 Vef.
- Self-powered fan.
Given set of teaching materials for the study of pulse generators
Ref.: 9EQCNJDAEP
Trainer for the study of the different circuits used in the pulse generation for thyristors and triacs, based on devices such as: UJT, DIAC, TCA-758, etc.
Composed by:
- 1 Block nº 363: transformer 12+12 V.
- 1 Block nº 393: pulse generator.
- 1 Block nº 333: B250 rectification bridge.
- 1 Block nº 355: pulse transformer.
- 1 Block nº 288: uni-junction transistor.
- 1 Block nº 296: triac.
- 1 Block nº 294: diac.
- 1 Block nº 265: potentiometer 10 K.
- 1 Block nº 268: potentiometer 500K.
- 6 Blocks nº 208: support for components.
- 1 Block nº 314: lamp holder.
- 2 Base plates for the assembling of the educational blocks.